Lockly PGD628WMB Secure Pro Latch, Wi-Fi Smart Lock with Fingerprint, Keyless Entry Door Lock with Patented Keypad,

This procedure will assist you  with installing the lockset step by step. Installation generally takes less than 30 minutes.If you have any questions please visit:LOCKLY.com/support.

Let's take a look at everything in the box.To complete this installation, you  will need a phillips head screwdriver,an optional flathead screwdriver, a ruler,a pair of needle nose pliers and an optional drill with a 1/2 inch drill bit. Let's start now!

Preparation

Remove any existing lockset from the door.

Prep the door if necessary.

Measure and confirm your door thickness is between 1-3/8 of an inch to 2 inches.

The cross bore hole must be 2-1/8 of an inch diameter.

The edge bore hole must be 1 inch diameter.

The back set should be 2-3/8 of an inch or 2-3/4 of an inch.

Install the lockset

Measure the back set and select the correct lock bolt.

For 2-3/8 of an inch back set, install back set F1.

For 2-2/4 of an inch back set, install back set F2.

Before installation,please note that the curved surface of the latch bolt must face in the direction that the door closes.

For in swing doors.

For out swing doors.

Attach the latch bolt into  the door using two screws (G).

Change handle for right or left swing doors While facing the door from the outside

If the door hinges are on the right side of the door,you have a right swing door.

If the hinges are on the left side of the door, you have a left swing door.

The lock ships default for right swing doors.

If you have a right swing  door you can skip this part.

For left swing doors,change the direction of the exterior handle.

Open the keyhole cover.

Insert the included key and turn the cylinder until the dots on the faceplate are aligned.

Use the clamping tool (R).

Simultaneously press the two release buttons on either side of the handle.

Remove the handle.

Rotate the handle 180 degree to the other side of the lock.

To re-install the handle,press the release buttons by hand and insert the handle back onto the lock.

Confirm that the buttons are flush with the handle.

Check to see if the handle works smoothly by rotating it in both directions

and making sure it returns to the idle position.

Remove the key and close the keyhole cover.

To change the orientation of the interior handle,unfasten the release screw on the inside of the interior assembly (N).

Change the orientation of the handle as needed.

Fasten the release screw to secure the handle at the desired position.

Aligning the release screw hole with either of the blue dots.

Prepare lock for installation

The upper portion of the lock set can  be secured with double-sided adhesive tape and optional fasteners.If you wish to have added stability, a drill is required if there are no  holes prepared for lock installation. Please refer to the provided  template for the drilling dimensions.

After the hole is drilled,Install the slotted barrel extension (U) to the exterior assembly (B) and securely tighten with a flat head screwdriver.

If you don't want to drill a hole,we have provided double-sided adhesive tape for you to help stabilize the lock during installation.

Peel the paper cover off of the exterior adhesive (T).

Insert the spindle (C) with  the holes aligning as shown.

Secure the spindle with the locking pin (D).

Carefully bend the end of the locking pin with the needle nose pliers.

Install the lock (exterior)

Pass the spindle through the center of the lock set and a round rods through the sides in their respective holes.

Guide the cable through the cross bore hole under the latch bolt.  

Insert two positioning rods (V) into the holes to the left and right of the spindle.

Align the lock straight and press hard if you use the adhesive tape to secure the top of the lock.

Prepare door sensor for installation

When installed on door, the distance between the wired sensor and sensor magnet must be less than 3/4 in order for the sensor to work.

If door frame is higher than door,add included foam pads to level parts double A and A B with each other as much as possible.

There may be circumstances where the sensor cannot be installed because of molding door limitations or is not aesthetically desirable.

The sensor wired to the lock is removable by carefully pulling its connector from the circuit board.

If removed, some features and  functionality will not be available such as real-time condition status.

When installing the door sensors, make sure the arrow of the wired sensor double A is placed next to the arrow of the sensor magnet A B as close as possible.

Do not install the sensor close to the strike plate.

The interior assembly comes with the pre-installed wired door sensor set up

for a right swing door with 2-3/4 of an inch back set.

Trim excess part for doors with 2-3/8 of an inch back set.

For left swing doors, re-route the door sensor  wire through the side channel.

Do not install the sensors yet.

Install the lock (interior)

If using adhesives to secure the upper part of the lock, remove the cover off of the  adhesive tape on the mounting plate.

Place the mounting plate on the door.

Ensure that the cable is guided through the rectangular hole near bottom of the mounting plate.

Make sure that the spindle and the positioning  rods are passing through their respective openings.

Align the mounting plate straight.

Secure the hole above the spindle with screw (O) Once the screw has been inserted correctly,make five turns clockwise by hand.Tighten the screw.

Remove the position rods (V) and replace them with two screws (O).

Once the screws have been inserted correctly, make five turns clockwise by hand.Tighten the screws.

If using fasteners to secure the upper part of the lock, select the appropriate optional screw M1 or M2 depending on your door thickness.

Finish securing the mounting plate to the door.

Plug in the cable from the exterior assembly  to the circuit board on the interior assembly (N).

Make sure that the plug is oriented correctly.

Matching the red side of the plug to the  red side of the socket on the circuit board.

Guide some of the excess length of the cable towards the exterior assembly.

Position the remaining length of  the cable away from the spindle area.

Position the interior assembly.

Ensuring that the spindle fits into the square hole and the interior assembly sits securely on the mounting plate.

Secure the interior assembly to the mounting plate using three screws (P).

Place four double A batteries into the battery box.

Check if the lock has started operating.

Close the battery box with the battery cover (Q).  

Secure it by fastening the battery cover screw at the top.

Install the door strike

Install the dust box (I) and the strike plate (H)  to the door jamb using two screws (G).

Install the door sensor

Peel off the paper layer of the adhesives from the back of the wired sensor double A.

Position the wired sensor double A to the edge of the door avoiding the door strike plate.

Align the arrow of sensor magnet A B with the wired sensor double A. They must be aligned or as closed as possible less than 3/4 of an inch.

Peel off the paper layer of the adhesives and install A B onto the door frame. 

Congratulations, you have successfully installed the lock.

This concludes the installation of the LOCKLY Secure Pro Latch Set. To enable live monitoring and voice assistance, you would need to pair with the secure link wi-fi hub included in the box. Please download the LOCKLY App from the App Store or Google Play first. Register and or login to your account and follow on screen instructions on how to connect to secure link wi-fi hub to complete the set up.

If you are interested in buying this product, don't hesitate to follow the link below

https://www.amazon.com/dp/B08435S8L7?ref_=cm_sw_r_cp_ud_dp_M25FSX58M6CF9NRFSQZG